- Bearing Wholesalers
- Single row bearing Double row bearing Multi-row bearing
English
العربية
Deutsch
Ελληνικά
Español
Français
Bahasa Indonesia
Italiano
日本語
Português
Русский язык
Shqip
Svenska
ไทย
Türkçe
Українська
Bearing Wholesalers
- Address258 Bearing Wholesalers Center Hill, Singapore 628925
- Factory Address258 Bearing Wholesalers Center Hill, Singapore 628925
- Worktime9: 00-18: 00 (بتوقيت بكين)
- Phone(Working Time)+6531591338
- Phone(Nonworking Time)+6531591338
- Fax+6531591338
Multi-row bearing
Contact NowFour-row cylindrical roller bearings are available in several designs:
- with a cylindrical or tapered bore
- open or sealed
Four-row cylindrical roller bearings are used almost exclusively for the roll necks of rolling mill stands, calenders and roller presses. Because they are normally mounted with an interference fit on the roll neck, four-row cylindrical roller bearings are well suited for rolling mill applications where the rolling speed is high.
Because four-row cylindrical roller bearings can accommodate only radial loads, they are mounted together with deep groove or angular contact ball bearings, or with tapered roller bearings (either radial or thrust design) which accommodate the axial loads.
Bearing features
- Exceptional high load carrying capacity
Because of their high number of rollers, four-row cylindrical roller bearings are suitable for very heavy radial loads. - Low friction (Roller end / flange contact area)
The open flange design, together with the roller end design and surface finish, promote lubricant film formation resulting in lower friction. - Long service life
The logarithmic roller profile reduces edge stresses at the roller/raceway contact and sensitivity to misalignment and shaft deflection. - Enhanced operational reliability
The surface finish on the contact surfaces of the rollers and raceways supports the formation of a hydrodynamic lubricant film. - Separable and interchangeable
The separable components of SKF four-row cylindrical roller bearings are interchangeable. This facilitates mounting and dismounting, as well as maintenance inspections. - High speed capability
The cage designs are suitable for high speeds, rapid accelerations and peak loads. - Low cross-sectional height
The low cross-sectional height of four-row cylindrical roller bearings allows for relatively large roll neck diameters compared to the roll diameter.
| Bearing Number | Bore Dia | Outer DIa | Width | Size |
|---|---|---|---|---|
| MEYLE Wheel Bearing Kit 014 033 0100 | 1 pcs | Negotiable | - | - |
| MONROE Bearing Bush, stabiliser L13820 | 1 pcs | Negotiable | - | - |
| A.B.S. Wheel Bearing Kit 201687 | 1 pcs | Negotiable | - | - |
| SNR Timing Belt Kit KD453.11 | 1 pcs | Negotiable | - | - |
| MOOG Bearing Bush, stabiliser OP-SB-6846 | 1 pcs | Negotiable | - | - |
| A.B.S. Wheel Hub 200022 | 1 pcs | Negotiable | - | - |
| FAG Wheel Bearing Kit 713 6114 90 | 1 pcs | Negotiable | - | - |
| A.B.S. Wheel Hub 201054 | 1 pcs | Negotiable | - | - |
| FEBI BILSTEIN Wheel Bearing Kit 07830 | 1 pcs | Negotiable | - | - |
| SWAG Anti-Friction Bearing, suspension strut support mounting 50 91 9924 | 1 pcs | Negotiable | - | - |
| FEBI BILSTEIN Wheel Bearing Kit 08840 | 1 pcs | Negotiable | - | - |
| A.B.S. Wheel Hub 200866 | 1 pcs | Negotiable | - | - |