- Bearing Wholesalers
- Single row bearing Double row bearing Multi-row bearing
English
العربية
Deutsch
Ελληνικά
Español
Français
Bahasa Indonesia
Italiano
日本語
Português
Русский язык
Shqip
Svenska
ไทย
Türkçe
Українська
Bearing Wholesalers
- Address258 Bearing Wholesalers Center Hill, Singapore 628925
- Factory Address258 Bearing Wholesalers Center Hill, Singapore 628925
- Worktime9: 00-18: 00 (بتوقيت بكين)
- Phone(Working Time)+6531591338
- Phone(Nonworking Time)+6531591338
- Fax+6531591338
Multi-row bearing
Contact NowFour-row cylindrical roller bearings are available in several designs:
- with a cylindrical or tapered bore
- open or sealed
Four-row cylindrical roller bearings are used almost exclusively for the roll necks of rolling mill stands, calenders and roller presses. Because they are normally mounted with an interference fit on the roll neck, four-row cylindrical roller bearings are well suited for rolling mill applications where the rolling speed is high.
Because four-row cylindrical roller bearings can accommodate only radial loads, they are mounted together with deep groove or angular contact ball bearings, or with tapered roller bearings (either radial or thrust design) which accommodate the axial loads.
Bearing features
- Exceptional high load carrying capacity
Because of their high number of rollers, four-row cylindrical roller bearings are suitable for very heavy radial loads. - Low friction (Roller end / flange contact area)
The open flange design, together with the roller end design and surface finish, promote lubricant film formation resulting in lower friction. - Long service life
The logarithmic roller profile reduces edge stresses at the roller/raceway contact and sensitivity to misalignment and shaft deflection. - Enhanced operational reliability
The surface finish on the contact surfaces of the rollers and raceways supports the formation of a hydrodynamic lubricant film. - Separable and interchangeable
The separable components of SKF four-row cylindrical roller bearings are interchangeable. This facilitates mounting and dismounting, as well as maintenance inspections. - High speed capability
The cage designs are suitable for high speeds, rapid accelerations and peak loads. - Low cross-sectional height
The low cross-sectional height of four-row cylindrical roller bearings allows for relatively large roll neck diameters compared to the roll diameter.
| Bearing Number | Bore Dia | Outer DIa | Width | Size |
|---|---|---|---|---|
| SWAG Radnabe 10 93 4321 | 1 pcs | Negotiable | - | - |
| A.B.S. Radnabe 200054 | 1 pcs | Negotiable | - | - |
| FEBI BILSTEIN Zahnriemensatz 34123 | 1 pcs | Negotiable | - | - |
| A.B.S. Radnabe 200218 | 1 pcs | Negotiable | - | - |
| SWAG Pilot Bearing, clutch 20 92 1298 | 1 pcs | Negotiable | - | - |
| FEBI BILSTEIN Shaft Seal, wheel bearing 03117 | 1 pcs | Negotiable | - | - |
| A.B.S. Radnabe 200022 | 1 pcs | Negotiable | - | - |
| OPTIMAL Radlagersatz 102019 | 1 pcs | Negotiable | - | - |
| MEYLE Radlagersatz 16-14 750 0011 | 1 pcs | Negotiable | - | - |
| SNR Wheel Bearing Kit R155.32 | 1 pcs | Negotiable | - | - |
| MEYLE Wheel Bearing Kit 614 160 4292 | 1 pcs | Negotiable | - | - |
| A.B.S. 200886 RADNABE | 1 pcs | Negotiable | - | - |